The cause of all these unable to load channels and auth failures in my opinion

Finally!!!! Stalker client is back working,

What I did was the following

Serial number: any 13 digits
Device ID: any 4 or more digits/I did 4 digits

Device ID2: any 4 or more digits/I did 4 digits
Signature: any 4 or more digits/ I did 4 digits.

Disable then enable stalker client 0.8.3 I'd it fails then disable then enable again until it loads.

*Must have a fresh mac

this works, but did not change the mac, now someone figure out the STB emulator please
 
Not sure if it will reset it, but the MAC will be orphaned, and the system clears those out periodically.

Ah because I entered a serial before changing my MAC, and now lost that serial after changing it and starting from scratch. Is there any way to reset the associated serial?

Update:
For those wondering it seems that changing the MAC address does reset the serial. With the servers getting hammered it was tough to tell which end the issues were.
 
Last edited:
Finally!!!! Stalker client is back working,

What I did was the following

Serial number: any 13 digits
Device ID: any 4 or more digits/I did 4 digits
Device ID2: any 4 or more digits/I did 4 digits
Signature: any 4 or more digits/ I did 4 digits.

Disable then enable stalker client 0.8.3 I'd it fails then disable then enable again until it loads.

*Must have a fresh mac

for those having problems uninstall the iptv stalker video addon first, then do as dafatmack writes above in the pvr client 0.8.3.
when you are sure that is working, install iptv stalker video addon and try migrate the settings.

it helps if you do one thing at the time and double checks, as you experienced it can easily be confusing at first.
so take it easy one addon/step at the time, you will slowly get better and it eventually it will become a lot easier.

practice makes champ. :) as said make sure one works with your credentials (numbers) and then slowly move on to next addon.
do not rush and enter lots of numbers change mac again and again, etc
if a mac fails move on to a new one do not reuse the same one right away as it still has serial attached to it until the server clear the unused mac's.

if you never had luck entering the serial and other stuff you might not need a "fresh" mac, as the one you have is probably still "fresh". heh

and if you primarily or only want iptv stalker video addon instead, start with that of cause.
 
Last edited:
Keep us posted thougjt I had to have stalker viedo addon to make
Pvr stalker client to work will uninstall and try to configure 0 8 3

"must have a fresh mac" ?

Can someone please clarify on this. I must be a newb. I thought mac address were permanent on android boxes. So I'm assuming you mean you need a new route to put your mac on? or how do I get a "fresh mac" on my KODI 15 Android box or route? I originally used the Stalker NFPSF addon, but now im stuck with the auth error on it.

I am trying with 0.8.4 stalker client, but I get "unable to load channels". I have put serials and digits as instructed, and tried both portal addresses , but still no luck. :confused:
 
"must have a fresh mac" ?

Can someone please clarify on this. I must be a newb. I thought mac address were permanent on android boxes. So I'm assuming you mean you need a new route to put your mac on? or how do I get a "fresh mac" on my KODI 15 Android box or route? I originally used the Stalker NFPSF addon, but now im stuck with the auth error on it.

I am trying with 0.8.4 stalker client, but I get "unable to load channels". I have put serials and digits as instructed, and tried both portal addresses , but still no luck. :confused:

For this server, the MACs for dedicated STBs like the MAGs or Avovs can not be modified by the user. However, for other users, including those who use generic andriod boxes, for Kodi add-ons or the STB emulator, the MACs are user defined, with the only requirement is that the first six characters are "00:1A:78".

To properly configure the serial number, and other fields, you may have to use a different MAC, or at least unlink the MAC by using a blank field in the donation checker, then relink your MAC. You also will need to have Kodi off, or at least disable Live TV when you configure the PVR client because the server will pick up the filled in details in Advanced when you initially connect with a "fresh" MAC".
 
for those having problems uninstall the iptv stalker video addon first, then do as dafatmack writes above in the pvr client 0.8.3.
when you are sure that is working, install iptv stalker video addon and try migrate the settings.

it helps if you do one thing at the time and double checks, as you experienced it can easily be confusing at first.
so take it easy one addon/step at the time, you will slowly get better and it eventually it will become a lot easier.

practice makes champ. :) as said make sure one works with your credentials (numbers) and then slowly move on to next addon.
do not rush and enter lots of numbers change mac again and again, etc
if a mac fails move on to a new one do not reuse the same one right away as it still has serial attached to it until the server clear the unused mac's.

if you never had luck entering the serial and other stuff you might not need a "fresh" mac, as the one you have is probably still "fresh". heh

and if you primarily or only want iptv stalker video addon instead, start with that of cause.


Ok, I'm still stuck. Any help would be greatly appreciated.

My IPTV Stalker works fine - so long as I leave the "Custom Serial" box unchecked. All channels work

My problem is Stalker Client - no matter what I do, I keep getting an "unable to load channels" error. I upgraded to the newest client just to be sure I wasn't on an old version, but that didn't work either. It's really weird IPTV Stalker works, Stalker Client does not.

Any ideas?
 
Ok, I'm still stuck. Any help would be greatly appreciated.

My IPTV Stalker works fine - so long as I leave the "Custom Serial" box unchecked. All channels work

My problem is Stalker Client - no matter what I do, I keep getting an "unable to load channels" error. I upgraded to the newest client just to be sure I wasn't on an old version, but that didn't work either. It's really weird IPTV Stalker works, Stalker Client does not.

Any ideas?

Please follow the instructions that have been posted. You need to use Custom Serial numbers and use the same information in all the clients that share the same MAC. Go reset your MAC and go here: http://iptvtalk.net/showthread.php?8798-Preventing-your-MAC-from-being-hijacked

For the PVR Stalker, make sure you disable Live TV while making the changes.