Hi Guys - running Openelec on an Intel Nuc and want to change from Salker to the PVR Stalker in readiness for change over that's coming. The problem is the built in PVR client in openelec dosen't work and there are no new NFPS PVR clients available for openelec. Will these surface soon ?. They are availalble for android, Windows and MacOS but not generic openelec for AMD/Intel chipsets.
NFPS / Private PVR Stalker Client NFPS for OPENELEC
- Thread starter jacksop2
- Start date
IPTV Private Server (NFPS)
Have a spare copy of Windows 10 Sandiver but don't want to go down that route if I can help it. Openelec was built to run Kodi and is super quick and efficient. Rather like using a stand-alone media player. Can't believe either NFPS or Openelec aren't considering releasing a PVR Client for it. There are 10's of thousands of openelec distros downloaded and is probably the best route to go for a truly independent media centre.
Please can you check and see what version it is? Its always 0.8.0 for any openelec 6.0 ive installed and that wont work at all for nfps. Tried multiple times setting it up. If yours is newer maybe it'll work. And I'm talking about x86_64 version. Not arm boards life RPI.
I dunno what you could be doing wrong.i just installed same version.2 minutes up and running.
I assume you installed pvr.stalker from openelec repo?
what are your settings?
Yep - using the PVR Client that came with openelec. Was told to use instructions for setting up with sub:
1. Go to System>Addons>My Addons>Video Addons>PVR
2. Click to open and then select configure
3. Select the “GENERAL” tab and set the “TIMEOUT” to 15 seconds
4. Then select “PORTAL 1” and enter your registered “MAC ADDRESS”
5. Set the “SERVER ADDRESS” to: 11.iptvprivateserver.tv
6. Then go to “SERIAL NUMBER” and put 13 characters using a mix of letters and numbers, I usually use: asdfg12345asd
7. You need to configure “DEVICE ID”, “DEVICE ID 2” and “SIGNATURE” with 4 characters all have to be different, e.g. 73nd
8. Then select “OK” to save the settings
9. Next select “ENABLE” to activate the PVR client
Anything look wrong Blackbear? Would love to get this going.
1. Go to System>Addons>My Addons>Video Addons>PVR
2. Click to open and then select configure
3. Select the “GENERAL” tab and set the “TIMEOUT” to 15 seconds
4. Then select “PORTAL 1” and enter your registered “MAC ADDRESS”
5. Set the “SERVER ADDRESS” to: 11.iptvprivateserver.tv
6. Then go to “SERIAL NUMBER” and put 13 characters using a mix of letters and numbers, I usually use: asdfg12345asd
7. You need to configure “DEVICE ID”, “DEVICE ID 2” and “SIGNATURE” with 4 characters all have to be different, e.g. 73nd
8. Then select “OK” to save the settings
9. Next select “ENABLE” to activate the PVR client
Anything look wrong Blackbear? Would love to get this going.
nothing sticks out other than I enter the server with http://
it should work as you have it though.
your getting unable to load?
are you using the same serial number,ect that your working iptv stalker is using?
if not reset your mac(change it by 1 number/letter) on papiao/iks66 and don't try iptv stalker,change your mac in pvr stalker to match.
enable live tv(the first time u will get unable to load),disable/enable live tv again and it should load second time.
it should work as you have it though.
your getting unable to load?
are you using the same serial number,ect that your working iptv stalker is using?
if not reset your mac(change it by 1 number/letter) on papiao/iks66 and don't try iptv stalker,change your mac in pvr stalker to match.
enable live tv(the first time u will get unable to load),disable/enable live tv again and it should load second time.
Getting the 'loading channel list' for about 30 seconds, then get 'PVR Stalker Failed' message. Have tried putting the 'Http' in front of the address. I'll try resetting my mac address as you've suggested and give it another go.
Thanks for your help Blackbear - am not giving up just yet !!
Thanks for your help Blackbear - am not giving up just yet !!
the pvr addon always fail the very first time you enable it for some reason. at least on android and windows and me and others.. heh
try get a link a new mac, then when it fails to load channels do not panic, re-enable the addon, the tv function, or restart kodi and it will load.
later versions of the addon automatically attempts to re-connect so you wont really notice it.
try get a link a new mac, then when it fails to load channels do not panic, re-enable the addon, the tv function, or restart kodi and it will load.
later versions of the addon automatically attempts to re-connect so you wont really notice it.