click the + and you can add icefilms or whatever to the home screen like xbmc.
after you've downloaded them from mickymarket
can load apps from the main screen
Last edited:
Mandatory Update
- Thread starter BIO
- Start date
click the + and you can add icefilms or whatever to the home screen like xbmc.
after you've downloaded them from mickymarket
can load apps from the main screen
just noticed a little problem with time zone,when ussing my time zone which was listed ,I get the wrong time,as if they where using day light saving time but my zone doesnt change,so have to go to one with 1 hour difference,to get the right time.but other wise from yesterday hick up ,love the machine quick and nice layout ,quick remote and very intuitive layout.this machine is a great addition to tv lovers in general offering some extras like movies,from stalker I love this little machine now sits on living room,and mag is in bedroom.
I need help plz... I factory reset my avov tv online + box and downloaded and tried both update.zip files and it comes up saying "NOT A VALID UPDATE PACKAGE!" I currently have the firmware 1.0.8 and i am attempting this update due to the fact that I cant get thru the "credentials" part of the activation of the iptv service. I purchased the year package from iks66,registered my mac,recieved my route # and in the username\pass section it wont allow the number to go thru. Please help!
That is an old file for the TVOnline avov box.
Is that the box that you have ?
It will not work on the Vixo models or the Fuse models, they have different file versions.
I do not even know how it is working on the TVOnline boxes, because it is an old file, but I do have it and will post as a mediafire link.
Give me a few minutes....
Is that the box that you have ?
It will not work on the Vixo models or the Fuse models, they have different file versions.
I do not even know how it is working on the TVOnline boxes, because it is an old file, but I do have it and will post as a mediafire link.
Give me a few minutes....
Okay guys here are the files. I have included all I had, including for the Vixo1 as well.
Use at own risk !
These release notes and these files are from the year 2015, so they are not release notes meant for today... But here you have it
VIXO 1
Step 1 Check which is your build number by going to “settings system info build number”
Step 2 first ensure which build is on your receiver now and use the corresponding file.
Rembmer do not extract any of the “update.zip” file, just copy it over
Step 3 Place the correct build update.zip file on a USBSD CardJump drive (do not unzip or change file name)
Step 4 Plug in the USBJump drive to the back of the device and power up your device. Click “local media” and a update message should come up.
Step 5 A Firmware update message will pop up and click “install”. If not browse the directory to find the “update.zip” file.
Step 6 Your device will restart and all the firmware update will be applied. After it’s done you should make sure you have build 1.0.11 from “settings system info build number”. Now you should be able to access MickyHop channel store once again. You can remove the jump drive when it prompts you to delete the file.
TVONLINE
Step 1 Check which is your build number by going to “settings system info build number”
Step 2 first ensure which build is on your receiver now and use the corresponding file.
Step 3 Place the correct build update.zip file on a USBJump drive (do not extract or change file name)
Step 4 Plug in the USBJump drive to the back of the device and power up your device
Step 5 A Firmware update message will pop up and click “install”
Step 6 Your device will restart and all the firmware update will be applied. After it’s done you should make sure you have build 1.0.11 from “settings system info build number”. Now you should be able to access MickyHop channel store once again.
1) To do this find an empty USB key and install the file I have attached called "update" on to it.
Notes: Do not unzip it, keep it as a zip file. Also make sure it is in the main directory of the USB (do not put it into another folder). Just in case, don't keep other files in there that you think might effect the installation.
2) Perform a factory reset and while in the first time setup menu plug in the USB (this is where the four main setting icons are). It should prompt you to do a firmware update in which you will say yes.
3) After this is done, your box will reboot again. After this you should have access to the channel store. If it still does not work you have a different issue with your box. Please do not try this for non TVOnline boxes. I advise you start a thread or open a support ticket with our website to get that issue fixed.
Use at own risk !
These release notes and these files are from the year 2015, so they are not release notes meant for today... But here you have it
VIXO 1
Step 1 Check which is your build number by going to “settings system info build number”
Step 2 first ensure which build is on your receiver now and use the corresponding file.
Rembmer do not extract any of the “update.zip” file, just copy it over
Step 3 Place the correct build update.zip file on a USBSD CardJump drive (do not unzip or change file name)
Step 4 Plug in the USBJump drive to the back of the device and power up your device. Click “local media” and a update message should come up.
Step 5 A Firmware update message will pop up and click “install”. If not browse the directory to find the “update.zip” file.
Step 6 Your device will restart and all the firmware update will be applied. After it’s done you should make sure you have build 1.0.11 from “settings system info build number”. Now you should be able to access MickyHop channel store once again. You can remove the jump drive when it prompts you to delete the file.
TVONLINE
Step 1 Check which is your build number by going to “settings system info build number”
Step 2 first ensure which build is on your receiver now and use the corresponding file.
Step 3 Place the correct build update.zip file on a USBJump drive (do not extract or change file name)
Step 4 Plug in the USBJump drive to the back of the device and power up your device
Step 5 A Firmware update message will pop up and click “install”
Step 6 Your device will restart and all the firmware update will be applied. After it’s done you should make sure you have build 1.0.11 from “settings system info build number”. Now you should be able to access MickyHop channel store once again.
1) To do this find an empty USB key and install the file I have attached called "update" on to it.
Notes: Do not unzip it, keep it as a zip file. Also make sure it is in the main directory of the USB (do not put it into another folder). Just in case, don't keep other files in there that you think might effect the installation.
2) Perform a factory reset and while in the first time setup menu plug in the USB (this is where the four main setting icons are). It should prompt you to do a firmware update in which you will say yes.
3) After this is done, your box will reboot again. After this you should have access to the channel store. If it still does not work you have a different issue with your box. Please do not try this for non TVOnline boxes. I advise you start a thread or open a support ticket with our website to get that issue fixed.
Code:
http://www.mediafire.com/file/pxfcq6blu6ssvee/build_1.0.07_TVOnline_update_-1.zip/file
Code:
http://www.mediafire.com/file/usc3iej48enymyt/build_1.0.08_TVOnline_update_-1.zip/file
Code:
http://www.mediafire.com/file/mq02b2406hh22ea/build_1.0.09_Vixo1_update_-1.zip/file
Code:
http://www.mediafire.com/file/ob11oub170t6u38/build_1.0.10_Vixo1_update_-1.zip/file