How to get Infomir logo back
- Thread starter theone
- Start date
Sorry, not yet! But you are right: WE MUST BE VERY CAREFUL!
INFOMIR has also made some changes in the Firmware and ssh rights mangment:
Code:
http://wiki.infomir.eu/doku.php/en:stb_webkit:faq:ssh_login_password
Code:
http://wiki.infomir.eu/doku.php/en:stb_webkit:faq:make_image_mag-200_250_newI will ask INFOMIR!
I have a MAG 254 (Infomir logo, ok!) and a "MAG 255" (AuraHD logo, deleted!)...
Manfred
Last edited:
I am getting Check Image status:invalid file header.
really its not a big deal its just a logo on boot up, it doesn't affect the box whatsoever.
really its not a big deal its just a logo on boot up, it doesn't affect the box whatsoever.
Maybe we will get here the answer, right from INFOMIR:
Code:
http://community.infomir.eu/426-boot-imageI have the same BOOT LOGO problem with a MAG 255 (AuraHD Plus).
And when we will get finally a positive answer for MAG 254 - if we must update with this image or that image - I would be able to do the same with MAG 255. Sure, the path may be another.
It seems there are images with and without the lost BOOT LOGO!
If so, we must only insert the correct path and must do the update.
It would be way out easier than with ssh...
----------
SOLUTION TO GET BACK THE RED INFOMR LOGO
I have now my BOOT LOGO on my MAG 255 back!
I found an INFOMIR site for MAG 255 (HD2 = AuraHD) with the files for r11 and especially two files are important:
- imageupdate
- imageupdate_logo
In the Header of the second one I found the following text:
...Logotype size: 44573...
Yor are remembering: Boot Logo Image should be compressed and max. 48 KB.
I took my USB stick and made Folder mag255 and into that mag255 folder i copied the file imageupdate_logo and renamed it to imageupdate.
In MAG 255:System settings > Software update > Update method
I changed the method from HTTP to USB.
Under Disk appeared: Kingston Data Traveler 2.0, my USB stick.
The update path changed to: /mag255/imageupdate
After starting the update from USB stick I had the same Firmware as before again, but WITH BOOT LOGO!
----------
So we are now looking on the MAG 254!
The update file source is:
Code:
http://soft.infomir.com.ua/mag254/release/0.2.18-r11/Inside this source collection you will find:
- imageupdate
- imageupdate_ul
The Header from the second file says:
...Logotype size: 41031...
In MAG 254:System settings > Software update > Update method
You nust changed the method from HTTP to USB.
Under Disk maybe appeared: Kingston Data Traveler 2.0, my USB stick.
The update path changed to: /mag254/imageupdate
Took your USB stick and made Folder mag254 and into that mag255 folder copy the file imageupdate_ul and rename it to imageupdate.
Please try it!
Manfred
Last edited:
Mag 254 LOGO BACK: Hope it helps others
I struggled with this issue for days and finally fix my box Mag 254 LOGO missing by doing this:
FIRST STEP
1).DOWNLOAD SOFTWARE-- Download and extract from
choose Mag 254
"bootstrap_254" and "imageupdate_ul" then rename both of them to bootstrap and imageupdate respectively.
2).Place the both files (imageupdate and Bootstrap) into a folder called mag254 on your USB stick
SECOND STEP (BIOS) WIPE THE BOX:
PLUG IN POWER SUPPLY > HOLD MENU BUTTON
Enter The BIOS. > choose “Def. Settings” > press the right. If Message "Wrong message" pops up IGNORE;
Press “OK”.> Select “Exit & Save” to save and exit.
STB will reboot automatically.
message ´Tftp load ´ will be on screen. Now unplug POWER lead.
FINAL STEP: (BIOS) FLASH THE BOX
1) Plug the USB Stick in the REAR USB Port
2) Power the STB on - press and hold the MENU button (just above the volume up button - you have to be quick)
3) Go to Upgrade Tools, then USB bootstrap.
This will then flash the STB with all your portal settings, be patient. Proceed with normal set up.
Credit not mine, goes to a brother in other forum I am a member.
I struggled with this issue for days and finally fix my box Mag 254 LOGO missing by doing this:
FIRST STEP
1).DOWNLOAD SOFTWARE-- Download and extract from
Code:
http://soft.infomir.com.ua/"bootstrap_254" and "imageupdate_ul" then rename both of them to bootstrap and imageupdate respectively.
2).Place the both files (imageupdate and Bootstrap) into a folder called mag254 on your USB stick
SECOND STEP (BIOS) WIPE THE BOX:
PLUG IN POWER SUPPLY > HOLD MENU BUTTON
Enter The BIOS. > choose “Def. Settings” > press the right. If Message "Wrong message" pops up IGNORE;
Press “OK”.> Select “Exit & Save” to save and exit.
STB will reboot automatically.
message ´Tftp load ´ will be on screen. Now unplug POWER lead.
FINAL STEP: (BIOS) FLASH THE BOX
1) Plug the USB Stick in the REAR USB Port
2) Power the STB on - press and hold the MENU button (just above the volume up button - you have to be quick)
3) Go to Upgrade Tools, then USB bootstrap.
This will then flash the STB with all your portal settings, be patient. Proceed with normal set up.
Credit not mine, goes to a brother in other forum I am a member.
Last edited by a moderator:
It's been 3 days I am seating in front of the tv w/ my laptop on my lap reading all kind of infos from different sites that I am member of. But, finally, I got this sticky that is so simple,so explicit that I got my logo going back on. Thank you guys Thank you HUMK and Thank you to where you got it from and Thank you to the guy who took his time and made it work. Today, I can seat and enjoy it real good with a satisfaction.
I really appreciate. Thanks again guys. Montochen
I keep getting a "Can't find......" message about the image file.... Tried everything. Hopefully when the next update comes out the boot logo will be back. Meanwhile I am going to just try and load just the "logo" pic by it's self.
I read sometime back that these files work for some Boxes: bootstrap_254.clean & imageupdate. In my box that combination did not work, but it worked for others. Can't think of a reason. Maybe (not sure) European build vs Chinese build. This is testing and I love it.
Did You Lose Your Infomir Logo?
Did You Lose Your Infomir Logo? Here is a fix.
Thanks to member at another site..
tested today and worked perfect.
C/P..
Here is a video to follow,
Code:
On the video there is a small mistake. You have to change the second ip as well. They dont show that on the video.
You will need these 2 files.Plus the Mcast program. I will stress this is only for the Mag254.
Mcast Program
Code:
Bootstrap_254
Code:
Imageupdate_ul
Code:
On the Mcast program on Stream 1 make sure you put the ip that shows up on your tv when you go into mcast in bio setting.
On Stream 2 you have to change some digits . Just up 1 on the last 2 numbers.
Here is a example,
Stream 1 ip 224.50.0.50:9000
Stream 2 ip 224.50.0.51:9001
The tv will show you when its done. Just close the Mcast program after its done as it maybe still running.
This will work if it doesnt work for you it might be because your anti virus is blocking.
Your all very welcome. Someone had to write this up.
Did You Lose Your Infomir Logo? Here is a fix.
Thanks to member at another site..
tested today and worked perfect.
C/P..
Here is a video to follow,
Code:
Code:
http://wiki.infomir.eu/lib/exe/fetch.php/:faq:video:multicast_update_.mp4On the video there is a small mistake. You have to change the second ip as well. They dont show that on the video.
You will need these 2 files.Plus the Mcast program. I will stress this is only for the Mag254.
Mcast Program
Code:
Code:
http://wiki.infomir.eu/lib/exe/fetch.php/mcast.zipBootstrap_254
Code:
Code:
http://soft.infomir.com.ua/mag254/release/0.2.18-r11/Bootstrap_254Code:
Code:
http://soft.infomir.com.ua/mag254/release/0.2.18-r11/imageupdate_ulOn the Mcast program on Stream 1 make sure you put the ip that shows up on your tv when you go into mcast in bio setting.
On Stream 2 you have to change some digits . Just up 1 on the last 2 numbers.
Here is a example,
Stream 1 ip 224.50.0.50:9000
Stream 2 ip 224.50.0.51:9001
The tv will show you when its done. Just close the Mcast program after its done as it maybe still running.
This will work if it doesnt work for you it might be because your anti virus is blocking.
Your all very welcome. Someone had to write this up.
Last edited:
this method worked for me tonight to get the infomir logo back up and going. just remember to change the box address in mcast! i had tried everything i could to get my logo back,even these files,but,i forgot 1 important step.
on line 1 in mcast you have to change :50 to what your box says on the screen ( mine says 100 ) then on line 2 where the :51 is i changed to 101 and viola loaded these images and logo is back and it only took maybe 5 to 10 minutes max.
Just one question that nobody has specified the answer to...... Do you only load one at a time? Or do you press both start buttons and do both files at the same time? Thank You.
Let both run at the same time for over an hour.... nada. I would give my left Kahuna to figure out what is wrong. Should the speeds be changed? I'll keep fiddling.
Did that. Trying again. Maybe I didn't let it run long enough. For giggles I just did the top. Took about 5 minutes then gave "wrong image" message. Then rebooted. Then I started it again and this time started both. The TV showed only the one ip addy, but packets were being sent from both top and bottom. Just going to let it run till the packet count matches the File size number the program shows. But it looks like it is going to take hours in my case. But Hey! Gotta learn sometime. 