Your STB is not supported

T

The Chairman

New member
Feb 26, 2015
10
0
0
#1
Hi everyone I have 3 Android boxes that I have been testing the 1.iptvprivateserver.tv on for the past few weeks and up the 3 days ago (when I went out of town) they were all working fine. Got back in town today and all three are giving me this message {Your STB is not supported in the center of the screen, and on the bottom, starting in the center there is a RED dot says Reload port, Next a YELLOW dot Account info, and next a BLUE dot Payment.}I have never seen the dot parts before like this.
The three Boxes are the T8 DroidBox Smart TV Box quad core 4.4 kit kat, The CS918 quad core 4.2, and a Jynxbox M3 4.1.
I have uninstalled the JynxBox, flashed it to factory firmware and reinstalled just the MXplay and Stalker STB Emulator 0.5.14 and still get the same message. I even took then to my work were I used the network there and still i get the same message. I haven't touch the other two boxes because everything was working 3 days ago.
I tried removing the IP address in the Emulator, I have tried to change the mac address, tried changing the serial nunber still no luck.

Does any one have any ideas. The up down thread says things are up

Thanks
 
#2
With version 0.5.14 you may want to update, since stb emulator is version 0.5.22 now. I have a copy of 5.21 and 5.22 in the third post HERE if you cannot get it from the play store.

There is also another emulator out now that works through kodi media player if you want to read up on that
 
Last edited:
#3
Are you get that message using that portal or different who is made to work for stalker too, but has extra security password and username? If is the second case emulator will not work, you need original MAG box and extra software for it, supported by provider.
 
Last edited:
#4
I have Tried all versions of Stalker from right from 5.14 up to 5.24 all came up with the same message.
I just installed Kodi version with stalker 3 built in and enabled live tv exit out of kodi then went in and enabled and configured stalker. all the channels came up but the none will play.
I know before when the old one was working with MX player I had to make sure that the hardware decoding was unchecked and software was checked is there anything like that which needs to be done with kodi setting.
 
#5
I had the same problem on one of my boxes today...I just add new portal & put in the info...back working again! Took only 5 minutes or less! I will update or upgrade to a more recent release! I did use different info when I created the second portal....then i deleted the first one that was corrupted or displaying the message! Working good now!!
 
#6
The chairman make sure you have entered the right ps info in the portal and then why not use the real last three set of your Mac on your device .
 
#7
Ok here is an update. I have flashed all 3 devices to factory settings. I have installed kodi on all three. I enabled live TV rebooted kodi . Then installed the stalker PVR client 5 and configured it.
I changed the last 6 of the mac address to match the device. Then enter the full server address
Http://1.iptvprivateserver.tv enabled it and reboot kodi again. And success looks like most of the channels are streaming.
So then I reinstalled the STB emulator 5.24 entered everything in to it the same way as I did in kodi and still get the same message STB not supported.
I'm very confused this isn't my first Rodeo and the where working and just stopped.
At least I have it in kodi now, but I learn that you can't use it in kodi if you use the Driodstick wizard to configure your device it makes Kodi crash.
Thank for all your help.
 
#11
Why are you putting addon to Kodi, when the standalone emulator works well.
Change last 6 digits on MAC
Change last 6 digits on seriel number
Make sure internal IP address is correct, some routers use 192.168.254.xx some use 192.168.0.xx others use 192.168.1.xx etc so make sure you select ip address in the range.
Http://1.iptvprivateserver.tv

thats all I did on my phones/tablet/android boxes/jynx live etc
 
#13
using the STB Emulator 5.24
OK here is the final out come. You do need to change at least the last 6 digits of the MAC address and the last 6 of the serial number.
Profile
NFPS
STB Model must be set to MAG 250 (this was my problem I was set to 260)
Portal http://1.iptvprivateserver.tv
MAC address you can use any 12 digits you want right now
Serial Number you can use any 13 digits you want right now
ip address works with 192.168.1.10 and works leaving it blank

reboot and should load

I am now testing it on the JynxBox Stick, on JynxBox HD, JynxBox M3, CS918 Quad Core and on the Zoomtak T8
at this point they are all streaming great on the VODS but seems to be hit and miss for the channels some freezing.
 
You must log in or register to reply here.
Top Bottom
Back
Menu